July 14, 2014

LC fiber patch in life has a lot of applications

Unshielded twisted pair has the basic categories of category 3 for phones and Category 5 for computer networks.UTP is under a catchment area of 100 meters.Meaning the cables should not exceed this length. TIA/EIA standards allow for 90 m of horizontal run (in the walls and ceiling).This leaves 10 m for patch cables (outside the walls.) Patch cables are utilized to connect devices in a room to the wall jack.There are physical limitations in the walls. Patch cables are utilized to connect devices in a room to the wall jack.Their physical limitations in the walls,access holes, HVAC(heating, venting, and air conditioned). Pipes, ducts,lights, fans and so on.Physical networking is not an easy task, if you need more distance than 100m,consider connecting a fiber optic cable to an intermediate distribution Facility (IDF).An IDF has its own 50m category 5 area it can cover fiber optic cables can be fixed as long as several kilometers.The LC Patch Cable is a small form factor (SFF) connector and is ideal for high density applications.LC fiber optic patch cord connector has a zirconia ceramic ferrule measuring 1.25mm O.D. with a PC or APC and, and provides optimum insertion and return loss.

Management hardware is the means by which by which fiber optic cable is routed, interconnected, and organized in a neat and manageable way.Once there are more than a few cables in an installation, unless they are managed neatly and effciently you will end up with a rat's nest of cabling, a tangled mess,and a hopeless mass of confusion.Management hardware allows fibers to be organized so they can be installed correctly and would be the behind-the-wall cables in a building network.These would run to the rear of the patch panel.Patch cable would then run between the patch panel and the equipment.By rearranging the fiber optic patch cables , you can connect ports on the equipment to different cables in the building.Another use for a patch panel is to form a transition point between multiplier cables and duplex cables.A72-fiber cable can connect to 72 separate adapters in the patch panel, individual or duplex cables then connect to the front of the patch panel.

The immediate tasks were tantamount to resolve a connectivity issue between buildings using existing fiber and to replace the existing switches. Each end of the fiber terminated in media converters. The older 62.5mm fiber SC ends simply needed conversion using an LC-LC Patch Cable to connect to the new fiber transceivers we installed. The 3-pair fiber cable only used the first air between the buildings, delivering less than 100Mbps through the media converters that were not power protected or a UPS.The LC jumper connector provides a secure locking mechanism to ensure the connection reliability. Customers use these LC fiber patch cords for demanding applications including ATM, Infiniband, Fast Ethernet, Gigabit Ethernet, Fibre Channel and anywhere they utilize LC GBIC's. Smaller LC connectors have double the port density of larger SC and ST style fibre termination making them very popular in high density applications.

Posted by: mikofy at 07:10 AM | No Comments | Add Comment
Post contains 510 words, total size 4 kb.

July 08, 2014

Fiber Patch Cord Power Measurement

Patch cables are commercially available from Thor Labs using the same visible fiber as used in FOC with Fiber connector-Physical Contact or FC connector.Some patch cables for both VIS-FOC and UV-FOC devices were constructed in the lab using a connectorzization tool kit and FC connectors. The user or the network technician can connect fiber optic Eth ernet ports to the fiber optic connectorson the horizontal cabling segment using straght-through fiber optic patch cables.They need not conecern themselves about the signal crossver,because it is already accomllishes in the fiber optic horizontal segment.on the other backone fiber optic cable systems that go between floors of a building,or between buildings on a campus,are usually wired straight through.When making a connection between an Ethernet switch port and a backbone fiber optic system,you need to make sure that the signal crossover is achieved in the patch cable at one of the link.LC Patch Cable which connector has zirconia ceramic ferrule measuing 1.25mm O.D. wth either a PC or APC endface, and provides optimum insertion and return loss.And precision optical cable manufacturing services can provide a wide range of standrad and custom cables. All cables are tested,serialized and labeled in individual bags with complete test in formation

Multimode patch cord optical loss power measurement is performed using the steps described in ANSI/TIA-526-14,method A.The patch cord is substituted for the cable plant.Because patch cords are typtically no longer than 5m, the loss for the optical fiber is negligible and testing can be performed at 850nm or 1300nm. The loss measured in thistest is the loss for the patch cord connector pair.ANSI/TIA-568-C states that the maximum loss fora connector pair is 0.75dB。

After setting up the test equipment asdescribed in ANSI/TIA-526-14,method A,clean and inspect the connectors at the ends of thepathc cords to be tested.Verofu that your test jumpers have the same optical fiber type and connectors as the patch cords you are going to test .The transmit jumper should have a mandrel wrap or modal conditoner depending on the revision ANSI/TIA-526-14 being used for testing.

Because both Fiber Optic Cord connectors are easily accdssible,optical power loss should be measured in both directions.The loss for the patch cord is the average of the two measuements.If the loss for the patch cord exceeds 0.75dB in either direction,the patch cord needs be repaired or replaced.

The fiber Optic Cord is mainly used on patch panel or for the connection between outlets and terminal equipment,The quality of connectors and fibers is mainly determined by the insertion loss and return loss.

Posted by: mikofy at 04:49 AM | No Comments | Add Comment
Post contains 424 words, total size 3 kb.

July 07, 2014

The development of optical fiber patch cable

Fiber optic cable has not been widely adopted for local area networks,however,because of its high cost of insallation.Networds that need extremely fast transmission rates,transminssions over long distances,or have had problems with elecriacal inteeference in the past ofen use fiber-optic cabling.

Fiber-optic cable is referred as either single-modd or multimode fiber.The term mode refers to the bundles of light that enter the fiber-optic cable.Single-mode fiber-optic cable uses only a single mode of light to propagate through the fiber cable,where multimode fiber allows multiple modes of light to propagatc.In multimode fiber-optic cable,the light bounces off the cable walls as it travels throuh the cable,which causes the singal to weaken more quickly.

Multimode fiber-optic is most ofen used as horizntal cable ,It permists multiple modes of light to propagate through the cable,which shotens cable dinstances and delibera less available bandwidth devices that use multimode fiber optic cable typically use light-emitting diodes to genarte the light that travels through that cable,however,highter bandwidth network devices such as gigabit eheemet are now usin lasers with mulitmode fiber-optic cable.The LC-LC Fiber Cable are used for non-permanent connections between patch panels, transmission equipment, etc. Pre-assembled cables allow for the implementation of complete "plug and play" solutions. When such a solution is adopted with accurate dimensioning and appropriate cable routing, it is possible to install even large cabling systems rapidly.

Single-mode fiber can be used for short distances,but due to its greater cost it is almost exclusively used for much longer distanc links in combination with LWL,ELWL or WDM solutions.Generally speaking,these solutions are designed for SMF cables with media designed for MMF can cause problems,SMF cables uses a much smaller diameter fibercord insinde the cladding:9/125um, They are usualy coloerd yellows,but like MMF cables they canbe ordered in other colors.Single mode optical fiber cable is commoly used as backbonecabling,it is also usually the cable type used in phone systems,Light travels through Fiber Optic Cords using only a single mode,meaning it travels straiht down he fiber and does not bounce off the cable walls .Because only a single mode of light travels throuht the cable,single mode fiber optical Cord support highter bandwidth and longer distances than mulitmode fiber optc cable.Devices that use single-mode fiber-fiber cable typically use laser to generate the light that travels through the cable.The Single Mode SC connector allows for quick and easy insertion via a snap-in mechanism and features a pre-radiused ceramic ferrule that minimizes back reflections.

ANSI/TIA/EIA-568-B recognizes62.5/125 micron.50/125 micron,and 8.3/125 micron single-mode optical fiber cables.ANSI/TIA/EIA-568-B states that the maximum backbone distance using single-mode fiber-optic cable is 3000 meters,and the maximum backbone distance using multimode fiber is 2,000 meters.

Posted by: mikofy at 06:24 AM | No Comments | Add Comment
Post contains 440 words, total size 4 kb.

July 03, 2014

patch cable fiber optic

Fiber Optic Patch Cord is an fiber cable that has fiber connectors installd on one or both ends. General use of these cable assemblies include the interconnection of fiber cable systems and optics-to-electonic equipment., A push/pull type fibre optic connector similar to SC but half the size. Often found on SFP/mini GIBC's and current generation switches. NXD LC/PC connector is available in both singlemode and multimode versions. Both singlemode and multimode versions come with a zirconia ceramic ferrule with pre-polished PC profile and convex shperical end. This allows for fast polishing of the fiber and enables the installer to achieve low optical loss, while ensuring maximum repeatability. LC connectors are used to attach fiber optic cable to SFPs and patch panels. An LC-LC Fiber cable has this connector on each end. It could be used to connect two roouters together, to connect a router to a 1Gbit or 2Gbit Fibre Channel device or switch, to a patch panel, or to mangy Gigabit Eehternet devices. These cables can be purchased in either MMF or SMF verions.

The LC Patch Cable is with a small form factor (SFF) connector and is ideal for high density applications. LC fiber optic patch cord connector has a zirconia ceramic ferrule measuring 1. 25mm O. D. with a PC or APC endface, and provides optimum insertion and return loss. LC-LC fiber optic patch cables are used to send high-speed data transmissions throughout your network. LC/LC fiber optic cables connect two components with fiber optic connectors. A light signal is transmitted so there is no outside electrical interference. Our LC/LC fiber optic patch cables are 100% optically tested for maximum performance. We have all lengths and connectors available

The LC Fiber assemblies are made to order in the usa and are fully tested to guarantee top performance. Each assembly is serialized for easy identification and sealed in individual Ziploc bags. Test results are included in each order. They are constructed with the highest quality components utilizing Glass and High grade Connectors with ceramic ferrules for increased durability and accuracy. Fiberstore offer all types of LC to LC fiber optic patch cables, the LC fiber optic cables, these cables are UPC or PC polish optional, with various kinds of fiber optic cable including Riser rated, Plenum rated and RoHS compliant. These multimode duplex LC fiber optic cables are custom length and cable colors. The cables can be with 50/125 or 62. 5/125 multimode optical fiber. OM3 multimode duplex fiber cables are also available on requestThe LC to LC fiber optic cable assemblies are made to order in the usa and are fully tested to guarantee top performance. Each assembly is serialized for easy identification and sealed in individual Ziploc bags. Test results are included in each order. They are constructed with the highest quality components utilizing Glass and High

Posted by: mikofy at 03:59 AM | No Comments | Add Comment
Post contains 475 words, total size 3 kb.

July 02, 2014

Fibestore supplies fiber optic patch cables

A variety fo fiber optic connector are used,depending on the cable type and the ethrenet media system.some connector has a key on an inner sleeve along with make the data flow,the ruansmit output of one transceiver must end up at the receive data of the other transceier,When connecting two nearby devices is connected to the receive data at the other device.

For horizontal fiber optic segmengts installed as part of structured cabing system,the connectors on the fiber optic cable should be oriented to achieve the crossover,For example,fiber optic cables are typically terminated in a set of fiber cable LC connectors located at the work area typically terminated in a set of fiber optic cable with two optical fibers in it,fiber#1 is connected to the A conector at the work area end of the segment and the B conector at the work area,and the A connector at the wirting closet.This way ,the user or the network on the horizontal cabling using straight through fiber optic patch cables.

Fiber optic patch cables are used for linking the equipment and components ,we have fiber optic patch cable with different fiber connector types,our low insertion loss and low back reflection .Axen Technologies fiber patch cable is widely applied in Telecommunication Networks ,Gigabit Ethernet and Premise Installations We fiber optic patch cable manufacturer in China,fiberstore supply fiber optic patch cable with different connector and cable type,Fiber optic patch cable is one of most commonly used components in fiber optic network. generally there are two types of fiber optic patch cords: single mode fiber optic patch cords and multimode fiber optic patch cable.

Here the word mode means the transmitting mode of the fiber optic light in the fiber optic cable core. usually single mode fiber optic patch cable are with 9/125 fiber glass and is yellow jacket color, multi mode fiber optic patch cables are with 50/125 or 62.5/125 fiber glass and is orange color.Duplex fiber cables consist of two fiber cores and can be either multimode or singlemode. We also can customize patch cables in any cut length.We offer competitive price for fiber optic patch cable, our company has strictly quality control system and high quality products,the custom fiber patch cable is fast delivery to worldwide customers.

Posted by: mikofy at 06:09 AM | No Comments | Add Comment
Post contains 379 words, total size 3 kb.

July 01, 2014

Custom Fiber Patch Cord

With the rapid expansion of network datacenters for both the private and public sectors, Amphenol Cables on Demand is seeing explosive growth in high-speed copper and optical cable products capable of speeds in excess of 10-Gigabits per second..As networks rapidly migrate to higher bandwidth over increased distances, the need for quick, easy-to-deploy solutions and future-proof designs from a trusted source is essential. Fiberstore,to deliver solutions that are designed to be better and create increased flexibility, greater efficiency and a superior network design.

fiberstore offering a complete line of products and systems ranging from high density fiber modules,cassettes and adapters to patch cords and harnesses, as well as fiber enclosures and trunk cables. This complete solution set provides the exceptionally high performance level that the Ortronics product line is known for, and unsurpassed integration with the rest of the physical infrastructure offering, such as some of our most popular cable items include our Fiber Optic Patch Cord,lc fiber cable,sc fiber cable and so on.

Fiber optic cabling is the medium of choice for longer distance and challenging cabling runs. These cables are thinner than copper patch cords and immune to EMI (Electromagnetic Interference) making them perfect for riser runs and uplink cables. There are two basic types of fiber cabling, single-mode and multi-mode.Howerver,there are something should be pay attentios when you are using the fiber path cords,Wavelength transceiver modules must be identical at both ends of the fiber jumpers, that must be the same at both ends of the fiber wavelength optical module, a simple distinction is the color of the light module to be consistent. Under normal circumstances, shortwave optical module using multimode fiber (orange fiber), long wavelength single-mode fiber module (yellow fibers) to ensure the accuracy of data transmission. Do not use excessive fiber bending and circling, this will increase the light attenuation in the transmission process. After using fiber jumpers must use protective sleeve protected fiber optic connector, dust and oil will damage the fiber coupling.

Fiberstore manufactures Optical Splitters and many kinds of fiber optic patch cords.Then Provide very fast logistics, as well as a very unique service system.If you want to customize products such as fiber optic cords, fiberstore is definitely a very good choice.

Posted by: mikofy at 08:59 AM | No Comments | Add Comment
Post contains 373 words, total size 3 kb.

<< Page 1 of 1 >>
29kb generated in CPU 0.0081, elapsed 0.0517 seconds.
31 queries taking 0.0456 seconds, 51 records returned.
Powered by Minx 1.1.6c-pink.