Posted by: mikofy at 07:09 AM | No Comments | Add Comment
Post contains 370 words, total size 3 kb.

Fiber optic ethernet systems are based on multimode and single mode fiber optic cables and connectors ,depending on the speed of the ethernet media system and the type and wave length of fiber optic transmitters used in the system,the behavior of fiber optic media can vary.This is especially true for the gigabit ethernet fiber optic system,which sends very high frequency signals over fiber optic cables.

There are a wide variety of fiebr optic cable types ,which are use according to the task at hand ,fiber optic patch cords typicallly consist of two fiebrs,either multimode or single mode depending on your requirements,patch cords can be quuipped with whatever,in the vast majority of structured cabling systems today,category 5 or 5e twisted -pair horizontal cables are used to deliver ethernet signals to the desktop,fiber optic backbone cables are commonly found in struchtured cabling systems,these backbone cables typically contain 12 or 24 fiebrs,but they may also contain dozens of fiebers ,for large baackbone cable installations,fiber optic cable manufactureds will build cables to order depending on your requriements.

single mode fiber has a much smaller core with the same 125um outer cladding commercial single mode fibers have core diameters that can vary over the range of approximately 8-10um ,they are collectively referred to as 10um fiber in the standard ,by way of comparison ,a human hair has a diameter of about 100um. A fiber optic mode is a path that light can follow in traveling down a fiber.As the name implies, multimode cables have a larger core designed to support multiple code, or patchs, of light propagation, then multiple paths of light from the LED are transmitted over the cable as showed in figure16-1. LC-LC Single Mode Patch Cord describes a fiber with a small core,only a few times the wavelength of light transmitted, that only allows one mode of light to propagate, it is commonly used with laser sources for high speed,long distance link.

A variety of fiber optic connectors are use,depending on the cable type and the ethernet media system,the most commonly used fiber optic connectors as of this writing are the ST and the SC connector,The ST connector is specified for use on 10BASE-FL equipment,A new connector called the MT-RJ is showing up on many ethernet hubs ,since it is compact and allows vendors to fit more fiber optic ports on a given hub module or faceplate other small form factor fiber optic connectors have been developed,such as the 3M volition VF45，and you may find these in use as well.For hormonal fiber optic segments installed as part of a structured cabling system,the connectors on the fiber optic cable should be oriented to achieve the crossover.The LC fiber patch cable connector is used on small diameter cable. The Cable Assembly Type is LC LC Fiber Patch Cord .

On the other hand,SC fiber products are commonly seen and SC fiber optic connectors are found on many equipment and cable assemblies. The LC-SC Patch Cord features its easy operation, good accuracy and low cost. backbone fiber optic cable systems that go between floors of a building,or between building on a campus are typically wired straight through when making a connection between an ethernet hub and a backbone fiber optic system you need make sure that the signal crossover is achieved in the patch cable at one end of the link.

Posted by: mikofy at 04:16 AM | No Comments | Add Comment
Post contains 565 words, total size 4 kb.

Several different types of connectors are available for fiber optic patch cables,such as LC,FC,and MTRJ,to name a few,However,the two most common types of fiber-optic connectors in use today are the ST-style and the SC-style connector ,Notice that the ST connector uses a barrel BNC-type adapter and the SC connector uses a block-style adapter,An easy way to reference these is the ST style connector is a stick-and-adapter,An easy way to reference these is the ST style connector is a stick and twist motion to connect the female connector over the male connector and twist to lock it in place and the SC connector is a stick and click motion to connect. LC LC fiber optic cables connect two components with fiber optic connectors , LC LC Fiber Patch Cord are used to send high-speed data transmissions throughout your network.

Fiber-optic cable is either single mode or multimode.In addition to this classification,fiber-optic cable is also designated by how it is sheathed,the two main classifications of sheathing are loose tube and tight buffered.loose tube cable consists of many individual strands of fiber-optic cable encased in a protective sheath known as a buffer tube ,which contains a strong material that provides additional strength for the entire sheath,Most loose-tube fiber-optic cables are sheathed in 250-micron weather protective material that can with stand aerial as well as underground installation,Loose tube cabling is usually found in out door fiber -optic installations.

many fiber optic patch panels use SC style connectors,whereas a significant amount of modern telecommunications equipments utilizes SC style connectors,This does not pose a problem because fiber -optic patch cables are available with LC-SC connectors（LC-SC Patch cord）,SC-SC connectors,and SC-ST connectors,Fiber-optic patch cables are available in many different lengths,it is a good rule of thumb to use the shortest cable possible to reduce the amount of slack in the cable,thus reducing the number of loops in the cable and reducing the possibility of violating the minimum loop rule..Fiber optic cabling is fairly new in comparison to copper media which has been in use for decades, fiber optic cable is make up of three main components:cord,cladding ,and protective coating ,extreme care must be taken during the manufacturing process to ensure that the highest-quality glass with the fewest impurities is created,

The protective coating can either be losse tube or tight buffered loose tube has many individual strands of cable sheathed together and tight buffered has a single strand in the protective sheath,fiber-optic cable has the ability to carry more data over longidistances than copper cable,making it suitable for many data and voice applications,fiber optic cable is more suitable for locations where a fire hazard exists,there is no chance of stray boltages causing sparks fiber opticcabling uses light waves called modes to transmit gignals from a transmitter to reciver,fiber optic cables is available in two main types:sigle mode andmultimode,single mode is more sutied for higher bandwidthy applications ,single mode is mor suitd for higher bandwdth applications over longer distances ,wheras multimode fiber -optic cable is more suited for shorter distances,

Single mode fiber optic cables(LC-LC Single Mode Patch Cord ) has a smaller diameter core;multiple fiber optic cabling ,attenuation are factors that degrade signal quality in fiber optic cabling,Attenuation is a law of physics regarding the behavior of light waves, there are variety of fiber optic connector types available,different telecommunications equipment manufactures make their equipment with different styles of connectors ,and fiber -optic patch cables are available to meet every requirement.

Posted by: mikofy at 08:08 AM | No Comments | Add Comment
Post contains 577 words, total size 5 kb.

Connectors and adapters are the plugs and sockets of a fiber optic system. They allow the data to be re-routed and equipment to be connected to existing systems.Connectors are intrinsically more difficult to design than mechanical splices.This is due to the added requirement of being able to be taken apart and replaced repeatedly.It is one thing to find a way to align two fibers, but it is something altogether different if the fibers are to be disconnected and re connected hundreds of times and still need to perform well.The main connectors encountered in multimode installations are the ST, SC, LC and MT-RJ.The LC-SC Patch Cord has SCconnectors on one end and a LC connector on the other end.

If two fibers are to be joined each fiber has a connector attached and each is then plugged into an adapter,An adapter is basically a tube into which the two connectors are inserted,it holds them in alignment and the connectors are fixed onto the adapter to provide mechanical support,An adapter is shown as part of figure 12.1.

Although different makes are sold as compatible, it is good practice to use the same manufacturer for the connector and for the adapter.The design of connectors originated with the adaptation of those used for copper based on coaxial cables,which were usually fitted by the manufacturers into a few metres of fiber called a pigtail which was then spliced into the main system.

Most connectors nowadays are fitted by the installer although pre-fitted ones are still viable,the benefit of using the pre-fitted and pigtailed version is that it is much quicker and easier to fit a mechanical splice or perform a fusion splice than it is to fit a connector,so there is some merit in allowing the factory to fit the connector since this saves time and guarantees a high standard of workmanship.

Single mode equipment is commonly fitted with the FC-PC，amongst others.Apart from the connector style itself ,one must also consider whether it is the single mode or multimode version,outwardly they look identical but a single mode connector and its core diameters of single mode fibers and the need for absolute accuracy when connecting them,Multimode fibers would be very happy in connectors designated as single mode,but putting single mode fibers into multimode connecting equipment would be inviting high losses. LC-LC Single Mode Patch Cord is the single mode fiber patch cord has the LC connector on each end

The LC LC Fiber Patch Cord has LC connectors on each end,when a connector is purchased,it always comes with a plastic dust cap to prevent damage to the polished end of the optic fiber,it is poor workmanship to leave fibers lying around without the caps fitted,Before considering the details of the various types of connector,we will look at the main parameters met in their specifications so that we can make sense of manufacturers' data.

Posted by: mikofy at 03:47 AM | No Comments | Add Comment
Post contains 482 words, total size 3 kb.

A wide variety of connectors can be used with fiber optic media,depending on the light emitting sources used to generate light pulses and the corresponding light-detecting sensors used to detect them,Figure 4-19 shows some connectors described in the following list: SC connector,ST connector,MT-RJ connector, LC connector.When the fiber optic patch cord ends of different interface, that can get a variety of fiber patch cable, such as LC-SC Patch Cord .

Fiber-optic cable trades electrical pulses for pulses light to represent bits.Because no electrical signals ever pass through the cable, fiber-optic media are as immune to electrical interference as any medium can get. Therefore, light pulses are unaffected by EMI and RFI.This characteristic also makes fiber-optic cables highly secure.They emit no external signals that might be detected, unlike electrical or broadcast media, there by eliminating the possibility of electronic eavesdropping.In particular, fiber optic cable is a good medium for high bandwidth, high speed,long-distance data transmission because of its lower attenuation characteristics and vastly higher bandwidth potential.Today, commercial implementations at 10,40, and 100 Gbps are in use.

Figure4-18 shows a typical fiber-optic cable.A slender cylinder of glass fiber called the core is surrounded by a concentric layer of glass called the cladding.The fibre is then jacketed in a thin transparent plastic material called the buffer.These three components make up to the mark what's labeled as the optical fiber in Figure 4-18.The fiber is optionally surrounded by an inner sheath made of colored plastic.A strengthening material, usually made of Kelar, comes next, followed by an outer sheath.Sometimes the core consists of plastic rather than glass fibers; plastic is more flexible and less sensitive to damage than glass, but attenuation is more of a problem than with glass.

Each fiber-optic strand carries data in only one direction,meaning fiber-optic network connections consist of two more strands,each in a separate inner sheath.However,these cables can be enclosed in a single sheath or can be two separate cables,each with its own sheath just as you have UTP patch cables,you also find fiber-optic patch cables,usually to connect from a fiber optic patch panel to a switch or router,Fiber optic patch cable used as back bone cabling often comes in bundles of 12 or more fiber strands,Even if you are using only two strands at first,it's good idea to run cable containing more fiber than you need ,in case a strand breaks during installation or you need additional strands for future growth.

Some testing has shown that glass fibers can carry several terabyte(1000 gigabytes) per second.There's really no end in sight for the bandwidth capacity of optical fiber.As network bandwidth needs s increase and the limits of copper wire are reached. Fiber optic cable will probably replace copper for all types of network connections,Table-4-2 summarizes fiber optic cablechareacteristics.And the singlemode fiber optic patch cables send one light signal at a time, and can be used for longer runs than multimode because they have more resistance to attenuation.Like the LC-LC Single Mode Patch Cord got a lot of applications in the everyday.

Medium interface connector-A medium interface connector is utilized to fiber distributed data interface like SC connectors MIC connectors are one-piece constructions.

Straight tip-Straight tip(ST) connectors join fibers of cross-connects or to optical devices.They are used most often in ethernet networks with fiber -optic cable as backbone cabling.ST connector locks onto the jack when twisted.

Straight connection-straiht connection(SC) connectors push on,which makes them easy to install and requires space for an attachment.They make a strong connection and can be used when splicing fiber-optic cables, a SC connector is a one -piece component, with two receptacles, fiber optic cables, a notch in its jacket ensures the correct orientation when inserted.

Locking connection-locking connection(LC) connectors push on and pull off with an RJ-45 style latching mechanism.The LC LC Fiber Patch Cord is adopted this connector on both ends here.They are about half the size of SC connectors, which make them good for high-desity applications, in which many fibers are concentrated in one location.

Posted by: mikofy at 04:13 AM | No Comments | Add Comment
Post contains 669 words, total size 5 kb.

Currently,as described,fiber is categozied into two groups:single-mode and multi-mode fiber,nevertheless ,there exists another kind of fiber like the POF .The mode refers to the path a photon takes in going from one side of the fiber to the other.According to the connection can be divided into:SC,ST, LC LC Fiber Patch Cord ,etc.

Single-Mode Fibers(SMF),In this type of fiber, all photons take the same path along the fiber,This is because the center of the fiber is very narrow.According to the ANSI the fiber has 8.5 micron core with 125-micron cladding. This factor reduces the signal loss and the ISI.Therefore,with single-mode fiber used primarily in telecommunications networks,fibers are characterized by long distance links and high capacity. LC-LC Single Mode Patch Cord are use as pigtails ,patch cords and jumpers to terminate directly into opto-electronic transmitters,receivers and other active and passive components.

It is the most reliable medium,but it has an important drawback for the fact that,at this moment,it is not clear that SFF connectors perform well with SMF connect two SMFs to the field ,As fabrication processes are improving quickly,it will be possible to have enough conncentricity in fibers as to connect them aligning their calddings.

Advantages of using SMF are well known:

Its bandwidth is enough to support,not only the current traffic but also the future one.

Greater distance:fiber can be run several kilometers.

Low attenuation:Light signals meet little resistance,so data can travel faster it has also some drabacks that can be reduced to one:

The core diameter is very small so,problems to access every home will arise.

The narrow size of the core causes that other elements of the system.

Currently,due to the great demand for increasing bandwidth,it has prompted the release of the 802.3z standard for Gigabit Ethernet over to allow the proper propagition of the laser VCSEL light along the multimode fiber.

The Mode conditionning patch cord is designed for long wave multimode applications of Gigabit Ethernet,It is compliant with this IEEE 802.3z application standard,This patch cord consists of connectors on each end of a cable assembly with single-mode fiber offset to a multimode fiber connection point in between.

The need for this patch cord is due to the single mode launch natrue of the LX or long wave transceiver modules used for gigabit ethernet,These modules have to operate for both center of a multimode fiber can cause multiple signals that confuse the receiver at the other end of the fiber,these multiple signals ,caused bu differentialmode delay effects,severely limit the cable distance lenghts for operating Gigabit Ethernet ,A mode conditionning patch cord eliminates these multiple signals by allowing the single-mode launch to be offset away from the center of a multimode fiber.bend in a fiber is function of the refrative index of the core and surrouding clading.Handling problems:it will become particularly acute for fiber to the home.for example the ends of the fiber must be perfectly aligned and as clean as possible.

Several different types of connectors are available for fiber optic patch cables such as LC,FC，to name a few。However,the two most common types of fiber-optic connectors in use today are the ST conector and the LC-SC Patch Cord ,notice that ST conector uses a barrel BNC -type adapter and the LC SC uses a block-style adapter.

Posted by: mikofy at 04:12 AM | No Comments | Add Comment
Post contains 548 words, total size 4 kb.

LC connectors are use to attach fiber optic cable to SFPs and patch panels ,an LC LC Fiber Patch Cord has this connectors on each end,It could be used to connect two routers together,to connect a router a 1 Gbit or 2Gbit Fiber Channel devices or switch,la patch panel,or to many Gigabit Ethernet devices.These cables can be purchased in either MMF or SMF versions.

LC connectors are used to attach fiber optic cable to GBICs and patch panels.A SC-LC cable has this connector on one end and a SC connector on the other end.It could be used to connect a router to an older Fiber Channel node or switch,to a patch panel,or to many Gigabit node or switch,to a patch panel,or to many Gigabit Ethernet devices,Some 2Gbit FC devices use GBICs and therefore SC connectors as well,and the router would require this cable to connect to them.These cables can be purchased in either MMF or SMF versions.

Multi-Mode fiber is utilized to short distances.It is less expensive than SMF,and is the most common cable type for use inside a data center or campus,These cables use a larger diameter fiber core on the inside of the cladding,Most often these cables are used with SWL GBICs and SFPs.be sure to check that the transceiver is designed to work with the cable diameter since there are two formats,brocade switches all work equally well with either format,so it should work as long as the transceiver is supported by brocade and matched to the cable.Usually, MMF cables are orange,but they can be ordered in non-standard colors so this is not a totally reliable way to distinguish them from SMF cables look for writing on the cable cladding as well.

LC-LC Single Mode Patch Cord can be used for short distances,but due to its greater cost it is almost exclusively used for much longer distance links in combination with LWL,ELWL or WDM solutions,Generally speaking,these solutions are designed for SMF cables,but it is appropriate to double-check since using SMF cables use a much smaller diameter fiber core inside the cladding:9/125 μm.They are usually colored yellow,but like MMF cables they can be ordered in other colors.'

The router itself may be considered IP/Ethernet network equipment when used for iSCSI or FCIP.Of data links,the router has sixteen SFP ports that support optical Gigabit Etheernet 1000baseSX connections These may be attached to a standard optical IP/Ethernet device such as a hub, switch,router, or host.

Different attachments require different cables. For example. LC-SC Patch Cord is needed and the other device uses GBICS instead of SFPs.In any case,it is necessary to ensure that media on both ends of the cable have the same wavelength, and that both are designed for the mode of the fiber optic cable connecting them.For management, the router has two RJ45 10/100 base T ports.These can be set up redundantly. They can connect to any standard 10/100 baseT Ethernet device. The most common connection is to a hub or switch.

Posted by: mikofy at 10:00 AM | No Comments | Add Comment
Post contains 500 words, total size 4 kb.

You may listen to the term hybrid or composite cable used.This cable does not constitute a special type of cable but is one that contains multiple smaller cables within a shared cable jacket or spiral wrap.The smaller cables can be the same type or a mixture of cable types.For example,a common cable that is manufactured now contains four-pair type or a mixture of cable types,For example,a common cable that is manufactured now contains four-pair Category 5e UTP cable and two different types of media to single location by pulling only one cable.A number of manufactures, build hybrid cables，however, fiber optic cable corresponds to the unique interface is one of the most frequent is LC, SC, ST these categories, especially LC-LC Single Mode Patch Cord . Then the article will introduce the details for these unusual kinds of fiber patch cable.

Composite cables are also offered by a number of distributors,Keep in mind that bunding Category 5e,6 or 6A UTP cables adversely affects their performance,so make sure that all the cables have been tested for standards compliance after they have been bundled,whether the bunding was done by the manufacturer or the distributor.

Picking the Right Patch Cables.Although not part of a discussion on picking cable types for horizontal cable,the subject of patch cords should be addressed,Patch cables are the cables that are used to connect 110-type connecting blocks,patch panel ports,or telecommunincation outlets to network equipment or telephones.

We've mentioned this before but it deserves repeating you should purchase factory -made patch cables,Patch cable are critical part of the link between a network device and the network equipment ,Determining appropriate transmission requirements and testing methodology for patch cords was one of the holdups in completing the ANSI/TIA/EIA-568B2.1 Category 6 specification,Low -quality,poorly made ,and damaged patch cables very frequently contribute to network problem,Often the patch cable is considered the weakest link in the structured cabling system,Poorly made patch cables will contribute to attenuation loss and increase crosstalk.

In the process of buying should consider the types of fiber optic jumper interface

The characteristics of LC LC Fiber Patch Cord : 8 Angle grinding, low insertion loss and high attenuation, metal parts, standard cubic zirconia ceramic core, fiber diameter, 3.0 mm in general, is used for optical fiber access network, data communication networks, fiber optic measurement instruments, optical fiber data transmission, etc

Factory-made patch cables are constructed using exacting and controlled circumstances to assure reliable and consistent transmission -performance parameters. These patch cables are tested and guaranteed under perform correctly.

Patch cables are made of stranded-conductor cable to give them additional flexibility,However,stranded cable has up to 20 percent higher attenuation values than solid-conductor cable,so lengths should be kept to a minimum,The ANSI/TIA-568-C standard allows for a 5-meter maximum-length patch cable in the wiring closet and a 5-meter maximum length patch cable at the workstation area.

Here are some suggestions to consider when purchasing patch cables:

Do not commit them yourself.Many problems result from faulty patch cables.

Choose the correct category for the performance level you wish to achieve.

Make sure the patch cables you purchase use stranded conductors for increased flexibility.

Purchase is a variety of lengths and make sure you get a few extra of each length.

Consider purchasing patch cords from the same manufacturer that rides the cable and connecting hardware, or manufacturers who has teamed up to provide compatible cable patch cords and connecting hardware.Manufacturers are part of such alliances。

In addition to the above introduction , LC-SC Patch Cord feature low cost, simplicity as excellent durability, ceramic ferrules of SC fiber optic patch cord makes them accurate alignment. These cables are for typical 50/125 and 62.5/125 optional Multimode Fiber. The cable diameter is 2mm or 3mm. SC multimode patch cord is available for PC/UPC/APC version, Dodo.Provide both simplex, duplex cable type and 0.9mm, 2.0mm, 3.0mm cable diameters for choose.

Posted by: mikofy at 07:10 AM | No Comments | Add Comment
Post contains 646 words, total size 5 kb.

Usually the fiber patch cord is divided into single-mode fiber and multimode fiber, the Single mode optical fiber core diameter is small, only on work at a given wavelength in single mode transmission, transmission band, large transmission capacity,Among them, more widely used is the LC - LC Single Mode Patch Cord .

In the context of ontogenetic experiments with the rotary joint,a fiber optic patch cord is needed to connected the light source and the rotary joint and yet another patch cord to connect the rotary joint and the fiber optic annual

The core and the cladding are two layers that make up to the mark of the lightguide.However, the light travels inside the core of the fiber optic, barely or not inside the cladding.For this reason, interconnected fiber-optics should have the same core diameter.Different cladding diameters have no influence on the coupling efficiency.

The buffer is a protective layer that tightly encircles the cladding.For patch cords, we usually recommend for use of use of another protective layer, called jacket, which is a loose tube converting the previously mentioned layers of the cable.

For a better fiber protection,we also offer larger jackets made of pvc tubing ,In this case,we use the following color convention,or we can use the black jacket if preferred,Metal jackets or jackets made of other materials are also available on request.

Mono fiber optic patch cords.The simplest form of the patch cord is a member of fiber with buffer coating and two ferrules on its ends.So far, most popular fiber in ontogenetic research is a fiber with a 200μm core diameters and NA=0.22. The fiber diameter and its numerical limit the coupling efficiency into the fibre therefore for higher coupling from sources like LEDs into an optical fiber of a specific diameter, shift to a higher NA fiber and follow up all the way through to fiber optics cannula.

The zironia ferrules are preferred for becoming less expensive,of tighter tolerance,harder,mass produced etc.However,dure to the fluorecence of the zirconia ferrules they are not called for applications involving fluoresecence measurements.

Dual fiber optic patch cords.A dual fiber -optic patch cord has two fibres -optic strands within the jacket, where the fiber ends are inserted into the mono or dual fiber ferrules or connectors.

Some dual fiber patch cords were especially intended to be easily the light from the two optical channels of the 1x2 rotary joint into a dual fiber cannula. There are several types of dual fiber patch cords, being dependent on the type of connectors and cannulas used.

Branching fiebr-optic patch cords.Branching fiber patch cord consists of multiple single fiber patch cords that are at one end joined within one connector and its ferrule, while the loose side of the patch cords ends with mono fiber ferrules or connectors,

We offer fiber optic patch cors that branch from one input to N out put connectors,These patch cords have a single FC or SMA connector on bundled fiber end ,and an FC，SMA,M3,zirconia or metal ferrule for each fiber on the other end, If the source is an LED or a lamp,the optical power entering the fiber bundle is divided between the channels,In the case of a lease ,please refer to the Mini cube section.

In addition to the above introduction, and multimode fiber optic jumper, multimode optical fiber is working at a given wavelength, with multiple inheritance fiber model colleague, but compared with the single mode of multimode optical fiber transmission performance is poorer, multimode optical fiber has a variety of different interface classification, including LC LC Fiber Patch Cord which provide 10 gigabyte data transfer speeds in high bandwidth applications, and they are five times faster - than standard 50 um fiber cables. These aqua OM3 10g 50/125 fiber patch cables are with LC connectors at the ends of them, and they work with both VCSEL laser and LED sources, besides , LC-SC Patch Cord is very widely used In our daily life.

Posted by: mikofy at 03:31 AM | No Comments | Add Comment
Post contains 663 words, total size 5 kb.

Four standardizedphysical implementations of Ggigabit Ethernet exist:

1000BSE-SX--A fiber optic implementation for a pair of multimode fiber.SX corresponds to short wavelength,lasers transmitting light at a wavelength of 850 nanometers are used.

1000BASE-LX--A fiberoptic implementation for a pair of single-mode or multimode fibers,LX corresponds to the long wavelength, lasers transmitting light at a wavelength of 1300nm are used.

1000BASE-CX--A short shielded copper cable used in wiring closets and equipment rooms.CX corresponds to copper.

1000BASE-T-- An unshielded twisted-pair implementation that operates across four pairs of Category 5 twisted-pair cabling.

Gigabit Ethernet runs on multimode and single-mode optical fiber.Some differences exist between the fiber optic transceivers used for Gigabit Ethernet and the ones that were used only for 10Mbps and Ethernet.

Although lasers were used for transmission across long-distance 10Mbps and 100Mbps Etherenet single-mode links,less expensive light emitting diodes (LEDs) were used for 10Mbs and 100Mbs transmission across shorter multi-mode fiber lines.However,LEDs cannot operate at 100Mps.At gigabyte speed,lasers are required for multimode fiber as well as single-mode fiber.

Fortunately,there is a type of laser at hand that is quite inexpensive and can be used with multimode fiber:the Vertical Cavity Surface Emitting Laser.VCSEL emitters transmitting light whose wavelength is 850nm can support gigabyte transmission across cables that are hundreds of miters in length.850nm laser transceivers are utilized in the short wavelength implementations.

The more costly lasers used for data transmission across single-mode fiber are operated at a wavelength for 1300nm for the long wavelength implementation. LX lasers are used with both multimode and single-mode cables.However,even with long wavelength lasers,multimode cable lengths are restricted to at most 550 meters. contrast,1000BASE-LX single-mode cables can be thousands of meters in length.

LX transmission across multimode fiber requires the help of a special mode conditioning patch cord.This type of patch cord is described in the LC LC Fiber Patch Cord ,after the discussion of fiber optic connectors that follows.

The recommended plug for 1000BASE-SX and 1000BASE-LX is LC-SC Patch Cord connetor,depicted in Figure 9.2.It is used for both multimode and single mode fiber optic gigabyte installations,this connector also is used for 1000BASE-LE.

A problem arises when a LX laser source is aimed at the center of the cord of a multimedia fiber.Multiple overlapping signals are created,and the receiver may not be able to interpreting incoming signals correctly. It turns out that offsetting the beam from the center of the multimode core solves the problem,An LX laser transmitter is connected to a special mode -conditioning patch cord that consists of a single mode fiber spliced to an off center position on a multimode fiber,the light beam is aimed into the LC-LC Single Mode Patch Cord end of the splice fiber.

The type of multimode fiber that is used in the patch cord must be the same ones type that is used in the attached cable run.

Posted by: mikofy at 06:04 AM | No Comments | Add Comment
Post contains 479 words, total size 4 kb.

Between the mechanical splice and patch panel B panel B is 400m of optical fiber.The loss of the 400m of optical fiber is 1.4db.The light energy entering the mated pair at patch panel B is -11.85dBm,which should be recorded on the vertical axis.As we already know,ANSI/TIA-568-C.3 allows a maximum loss of only 0.75dB for a mated pair.The minimum amount of light energy exiting the mated couple should be -12.6dBm.If we ignore the loss for the 5m patch cord between patch B and the receiver,the power available to the receiver is -12.6dBm.This is the absolute value recorded on the vertical axis.

The next in this process is tantamount to record the horizontal axis values.Working from left to right starting at the transmitter,the first value recorded on the horizontal axis is zero.It is taken from this point that we will record the successive segments of optical fiber.

The opening segment of optical fiber is the 5m patch cord.With an overall length of 810m,it's not practical to draw the 5m patch cord to scale unless you have a very large sheet of paper.Looking at Figure 32.4,you can see that the first segment on the horizontal axis long enough to clarify that the 5m patch cord is a separate segment of optical fiber.The second value registered on the horizontal axis is 5m.The LC LC Fiber Patch Cord is housed in a LSZH (Low-Smoke, Zero-Halogen) flame retardant jacket, to ensure minimal smoke, toxicity and corrosion when exposed to high sources of heat, in the event of a fire – an ideal solution for use in industrial settings, central offices and schools, as well as residential settings where building codes are a consideration.

The second segment is a 400m span of optical fiber from patch panel A to the mechanical splice. The second segment is a 400 spans of optical fiber from patch panel A to the mechanical splice.The resulting value recorded on the horizontal axis si 405m.

The third segment of optical fiber is a 400m span from the mechanical splice to patch panel B，the succeeding value recorded in optical fiber is 400m span from the mechanical splice to patch panelB，the resulting value recorded on the horizontal axis is 805m.

The concluding segment of optical fiber is the 5m patch cord that connects the receiver to patch panel B.The last value recorded on the horizontal axis is 810m.

All the values for the vertical and horizontal axes are recorded. The final step is to draw a series of lines that graphically represent the recorded values. the first line segment will be a horizontal line from -8.0dBm on the vertical axis to the 5m point on the horizontal axis, this line represents the patch cord that connects the transmitter to patch panel A,The line is horizontal because the patch cord loss is insignificant At the end of this ,vertical line will be drawn that runs from -8.0dBm;it represents the loss for the mated pair at patch panel A. these cables are UPC or PC polish optional, with various kinds of fiber optic cable including Riser rated, Plenum rated and RoHS compliant. These multimode duplex LC-SC Patch Cord are custom length and cable colors. The cables can be with 50/125 or 62.5/125 multimode optical fiber. OM3 multimode duplex fiber cables are found on request.LC-LC Single Mode Patch Cord are made strictly depending on industry and international standards. They are 100% tested during the production. Accessories including the connectors, adapters and attenuators are available

The third line will extend from the 5m point on the horizontal axis to the 405n point. It will be a sloping line from left to right that goes from-8.75dBm on the vertical axis to-10.15db.This line is the loss for the 400m section of optical fiber from patch panel A to the robotic space.At the end of this line,a vertical line is drawn from -10.15dBm to -10.45dBm to represent the loss for the mechanical splice.

The fifth line will extend horizontally from the 405m point to the 805m point.This line will slope from-10.45dBm on the vertical axis to --11.85dBm;it represents the loss for the 400m section of optical fiber from the mechanical splice to patch panel B，At the end of this line ,vertical line will be drawn from-11.75dBm to -12.6dBm.Representing the loss for the mated pair at patch panel B.

The closing line drawn is a horizontal line from the 805m point on the horizontal axis to the 810m point.This line represents the patch cord from patch panel B to the receiver. There is not any slope in this line because the loss for the patch cord is insignificant.If everything has been drawn correctly,your drawing should look like Ffigure 32.4.

Posted by: mikofy at 09:12 AM | No Comments | Add Comment
Post contains 786 words, total size 5 kb.

Fiber optic cable,or simply fiber,contains one or several glass or plastic fibers at its center,or core,Data is transmitted via pulsing light sent from a laser (in the case of 1- and 10-gigabit technologies)or an LED (light emitting diode)through the central fibers.Surrounding the fibers is a layer of glass or plastic called cladding.The cladding has a different density from the glass or plastic in the strands.This reflection allows this fiber to bend around corners without diminishing the integrity of the light based signal.Outside the cladding,aplastic buffer protects the cladding and cord,Because the buffer is opaque,it also absorbs any light that might escape,To prevent the cable from stretching,and to protect the inner cord further,strands of Kevlar surround the plastic buffer,a plastic sheath covers the strands of Kevlar.

Like twisted pair and coaxial cabling, fiber optic cabling comes in a number of different varieties,depending on its intended use and the manufacturer.For example fiber-optic cables used to connect the facilities of large telephone and data carrier may contain as many as 1000 fiber and be heavily sheathed to prevent damage from extreme environmental conditions.At the other end of the spectrum, fiber optic patch cables for use on LANs may contain only two strands of fiber and be pliable enough to wrap around your hand.Because each strand of glass in a fiber optic cable transmits in one direction only -in simplex fashion -two strands are needed for full-duplex communication,one solution is to use a zip cord cable,in which two strands are combined side by side in conjoined jackets. You will find zip cord where fiber optic cable spans relatively short distances short distances such as connecting a server and switch.A zip cord may come in one of many types of connectors on its ends as described later in this section. the most significant drawback to the use of fiber is that covering a certain distance with fiber optic cable is more expensive than using twisted pari cable also,fiber optic cable requires special equipment to splice,which means that quickly repairing a fiber optic cable in the field can be difficult ,fiber's characteristics are summarized in the following list:

Cost-fiber optic cable is the most expensive transmission medium ,because of its cost most organizations find it impractical to run fiber to every desktop not only is the cable itself more expensive than copper cabling but fiber optic transmitters and connectivity equipment can cost a much as five times more than those designed for UTP networks In addition,hiring skilled fiber cable installed costs more hiring twisted pari cable installed.A variety of high quality single mode and multimode fibre, LC-LC Patch Cable assemblies in various configurations and lengths. All fibre patch leads are LSOH rate. Ultimate versions are available in grey or orange with our single mode patch leads being available in yellow. Fibre patch cables are recommended for connections between fibre patch panels, hubs, switches, media converters and routers, etc. Fibre optic cables provide higher speeds and increased bandwidth, compared to conventional twisted-pair copper cable.

Connectors-wiht fiber cabling,you can use any of 10 different types of connectors :the SC,ST ,LC,and MT-RJ，Existing fiber networks might use ST or SC connectors,However,LC and MT-RJ connector are used on the very latest fiber optic technology,LC and MT-RJ connectors are used on the very or latest fiber -optic technology,LC and MT-RJ connectors are preferable to ST and SC connectors because of their smaller size which allows for a higher density of connections at each termination point, LC Patch Cables provide physical separation for up to 12 networks, applications or organizations.The MT-RJ connector is unique because it contains two strands of strands of fiber in a single ferrule,which is short tube within connector that encircles the fiber and keeps it properly aligned,With two strands in each ferrule,a single MT-RJ connector provides for full duplex signaling,linking single mode and multimode portions of a network.Refer to figure to see a converter that connects multitude fiber with an ethernet network using UTP.

Posted by: mikofy at 04:25 AM | No Comments | Add Comment
Post contains 662 words, total size 5 kb.

Unshielded twisted pair has the basic categories of category 3 for phones and Category 5 for computer networks.UTP is under a catchment area of 100 meters.Meaning the cables should not exceed this length. TIA/EIA standards allow for 90 m of horizontal run (in the walls and ceiling).This leaves 10 m for patch cables (outside the walls.) Patch cables are utilized to connect devices in a room to the wall jack.There are physical limitations in the walls. Patch cables are utilized to connect devices in a room to the wall jack.Their physical limitations in the walls,access holes, HVAC(heating, venting, and air conditioned). Pipes, ducts,lights, fans and so on.Physical networking is not an easy task, if you need more distance than 100m,consider connecting a fiber optic cable to an intermediate distribution Facility (IDF).An IDF has its own 50m category 5 area it can cover fiber optic cables can be fixed as long as several kilometers.The LC Patch Cable is a small form factor (SFF) connector and is ideal for high density applications.LC fiber optic patch cord connector has a zirconia ceramic ferrule measuring 1.25mm O.D. with a PC or APC and, and provides optimum insertion and return loss.

Management hardware is the means by which by which fiber optic cable is routed, interconnected, and organized in a neat and manageable way.Once there are more than a few cables in an installation, unless they are managed neatly and effciently you will end up with a rat's nest of cabling, a tangled mess,and a hopeless mass of confusion.Management hardware allows fibers to be organized so they can be installed correctly and would be the behind-the-wall cables in a building network.These would run to the rear of the patch panel.Patch cable would then run between the patch panel and the equipment.By rearranging the fiber optic patch cables , you can connect ports on the equipment to different cables in the building.Another use for a patch panel is to form a transition point between multiplier cables and duplex cables.A72-fiber cable can connect to 72 separate adapters in the patch panel, individual or duplex cables then connect to the front of the patch panel.

The immediate tasks were tantamount to resolve a connectivity issue between buildings using existing fiber and to replace the existing switches. Each end of the fiber terminated in media converters. The older 62.5mm fiber SC ends simply needed conversion using an LC-LC Patch Cable to connect to the new fiber transceivers we installed. The 3-pair fiber cable only used the first air between the buildings, delivering less than 100Mbps through the media converters that were not power protected or a UPS.The LC jumper connector provides a secure locking mechanism to ensure the connection reliability. Customers use these LC fiber patch cords for demanding applications including ATM, Infiniband, Fast Ethernet, Gigabit Ethernet, Fibre Channel and anywhere they utilize LC GBIC's. Smaller LC connectors have double the port density of larger SC and ST style fibre termination making them very popular in high density applications.

Posted by: mikofy at 07:10 AM | No Comments | Add Comment
Post contains 510 words, total size 4 kb.

In many situations, we have to have a demountable connection between fibers, between a fiber and a source or a detector, or between different fiber optic instruments.Demountable connections are achieved using fibers with connectivity terminations.Differrent designs of connectors have been prepared over many year with that the aimof reducing the loss or for ease of connection,The connector should ensure that the fiber core is alingned with the laser or the dector or the fiber to whinch itis being connectred .Due to the smallness of the core of the fiber,connectors are high-precision devices with tolerances of less than 1 um,Connector losses between two fibers will be minimized if the fibres are identical and perfectly aligned and touch each other,Any gap between the two fibers will lead to a small loss but also to reflections,It is possible to reduce back reflection b using angle-polinshed end faces since reflection from the ends do not couple back into the fiber provided that the angle of the polish is chosen appropriately .In a connector, the fiber ends are polished and fixed, any dirt on the fiber end can lead to losses when the connector is utilized.

Each connector consists of four major componets the ferrule the connectorbody the cable ,and the coupling device,the ferrule is a long,thin cylindraical device, ussually made of metl or ecramic,wiht a holedrilled thouht its cenre,the hole diametre is silightly larger than the cladding diameter so the fiebr can be positioned sungly within the ferrule ,connectors with different ferrule shapes or finisshed are available ,most currently used ferrules allow for physical conact betwwn the two fiber being connected,better physical contact is achieved by using a conves surface for the ferrules,

The connector body is usually made out for metal or plastic and holds the ferrule that carries the fiber ,the ferrule extends beyond the connector body so as to be able to connect to another connector ,the cable jacket and strength members are usually bonded or crimped to be connector body ,the cable is attached to be body of the connector and a acts as the point of entry for the fiber,the coupling device helps in the alignment of two fibers ,There are several types of fiber optic connectors available today. The most common is ST, SC, FC, MT-RJ and LC style.LC-LC Fiber Cable are utilized to send high-speed data transmissions throughout your network.The LC fiber patch cable is just a tiny form factor (SFF) connector and is ideal for high density applications.The LC fiber patch cable has a zirconia ceramic ferrule measuring 1.25mm O.D. with either a PC or APC and provides optimum insertion and return loss.The LC Patch Cable connector is supported in small diameter mini-cordage (1.6mm/2.0mm) as well as 3.0mm cable. LC fiber patch cable connectors are available in cable assembled or one piece connectors

Fiber Optic Cord are the simplest fiber optic elements,consinsting of shor length fo opticalfiber with a connetor on either end,Since they are used to connect various componentsand instruments in a fiber optic system ,their chareacteristics in term of loss and aging determine the oveall performance of the system ,Inprinciple,When two patch cords are connected ,if the fibers are identical,it should result in alomost zero loss,in actual pratice the loss may not be very small sincethe fiber may not be completely concentric wiht the connector centor center,there could be dust at the tip of the connector,or there could be misalignments when two patch cords are mated ,Patch cords with differnt tys fo fiber and different conncetor types are available Typical insertion loss of patchd are about 0.4 dB ,with a return loss fo better than 50.DB.

Posted by: mikofy at 03:51 AM | No Comments | Add Comment
Post contains 611 words, total size 4 kb.

Be ordered separately,other than as part of the entire front or rear body writing harness can be ordered separately,other than as part of the entire front or rear body wring harness,where are you aftermost produces?however ,Fiber Optic Cord can be purchased from some scientific suppliers in various from some scientficsuppliers in various diameters and lengths ,or floor from dealer in custom ban parts in the meantime ,here are some brilliant ideas from john practical on how to make the most of damaged fibre optics.

A severed fibre optic cord looks likes this and must be cut off clean before the connection can be made ,if the break is very near the end for the cord,look at ways of releasing some of the fiber optic cord from the harness so that you can ease it through to a shorter route and make a direct connection to the lamp.

dimmed fibre optics can often be improved by cleanning road grime and dirt from the back fo headiamps,On the other hand ,if none fibre optic has had to be reparined leaving one trm signal light in the cockpit brightre than the other you could try spraying a little aluminum paint over the back of headlamp on the googd side to diminish the amount of light transmitted and match it with the repaired sied,Alternatively you could try increasing the amount of light getting into the fibre optic cord on the repaired side.LC Patch Cable is the small compact form LC fiber optic connector. It presents the RJ-45 style interface with low insertion loss and low back reflection. It is with extreme precision alignment and is widely used all over the world. And both Simplex LC cable and duplex LC cable. The connector is 1.25mm O.D zirconia ceramic ferrule; LC fiber cable can be 9/125 single mode or 50/125 multimode or 62.5/125 multimode, PC, UPC or APC and face. It is compliant to TEA/TIA and IEC standards .These LC-LC Fiber Cable including single mode and multimode types, in simplex and duplex versions. Cables can be Rizer rated or plenum rated, with LSZH cable and RoHS compliant cables available

signals can be made brighter by redrilling the cords socket at an angle so the cord is aimed more accurately at the bulbs filament decreasing the distance between the filament and the fibre optic by one half is said to increase the light in the passenger compartment by four times.

As we said earlier ,you may be able to purchase new lengths of fibre optic cord but you would haveto disguise them anywhere that would turn a concourse judge's head The cost of installing an individual cord would be far less than a complete hamrness however because none of the electrcal connections would have to be remade afremarket hamessea are now becoming abailable for those occasions when you do need to replace the comolete harness,such as in a total restoation or after a part fire if you are fortuate enough to locate an original GM body wiring harness for those cars containning fibre optics cords you can occasionally pick them up at swap meets or through enthusiast advertisements in club magazines these are the part mumbers to look out for.

Posted by: mikofy at 06:17 AM | No Comments | Add Comment
Post contains 540 words, total size 4 kb.

Fiber optic cable commonly referred to as fiber patch or fiber jumper cables, fiber optic cable is terminated at both ends of the connector. It has two main application areas: computer workstation outlet and patch panels or optical cross-connect distribution centers. They are intended for indoor applications.The optical fiber cables are extensively used in the modern world for high speed data transfer. These cables are used for setting up large-scale infrastructure such as telecommunications backbones and the Internet under-ocean cables. The tremendous speed of transfer, low attenuation, high speed, high bandwidth and high security factors are some of the remarkable characteristics of these cables. To tie up two ends of such high-quality cables, one needs to use bridges of good quality. These bridges have to support the high speed, low attenuation and all other positive attributes of the optical transmission channels. And a fiber optic patch is capable of supporting all of it.

Nevertheless, you will find a minimum of 3 kinds of typical multimode materials to select from. sixty two. 5/125um multimode dietary fiber (also known as OM1), 50/125um multimode dietary fiber (also known as OM2), as well as 10Gig laser beam optimized 50/125um multimode dietary fiber (also known as OM3).

Amongst LC Patch Cable, generally you simply worry about the actual attachment reduction that ought to end up being a maximum of 0. 3 in order to 0. 5dB.LC dietary fiber area wires are available in a variety of designs, for example LC in order to FC, LC in order to STREET, LC in order to SOUTH CAROLINA, LC to LC, LC to MTRJ, and much more. LC materials will also be obtainable in simplex as well as duplex designs.

LC-LC Fiber Cable is a fiber optic cable that can be directly connected to other equipment for connecting and managing convenience. It is used for making patch cords from equipment to fiber optic cabling. Having a thick layer of protection, it is used to connect the optical transmitter, receiver and the terminal box.Optical Cord used as cross- connect jumpers, equipment and work area cords in fiber 0ptic telecommunications and FTTH (Fiber To The Home)

In the current sophisticated globe associated with wish associated with higher pace conversation along with superlative high quality associated with protection, dietary fiber optic systems perform a vital part. These types of wires have information as well as info within type of gentle influx. They're higher pace conversation stations along with minimum attenuation associated with transmission. Consequently, the actual transmission tranny happens along with nearly unequaled high quality.

The actual higher pace, reduced barrier as well as precise information link that's acquired through implementing a good optical dietary fiber system is the greatest within course these days. Consequently, these types of systems would be the types associated with choice whenever information is actually transported in one spot to an additional. Nevertheless, it's not practical in order to presume which this kind of wires will be offered at just about all feasible measures preferred. The truth is within the unlike this particular. Consequently, 1 will have to sequentially arranged several this kind of wires upward inside a pipeline once the bodily range associated with conversation surpasses the actual cable duration. The dietary fiber optic area performs an excellent part in this scenario.

Posted by: mikofy at 04:10 AM | No Comments | Add Comment
Post contains 553 words, total size 4 kb.

Patch cables are commercially available from Thor Labs using the same visible fiber as used in FOC with Fiber connector-Physical Contact or FC connector.Some patch cables for both VIS-FOC and UV-FOC devices were constructed in the lab using a connectorzization tool kit and FC connectors. The user or the network technician can connect fiber optic Eth ernet ports to the fiber optic connectorson the horizontal cabling segment using straght-through fiber optic patch cables.They need not conecern themselves about the signal crossver,because it is already accomllishes in the fiber optic horizontal segment.on the other backone fiber optic cable systems that go between floors of a building,or between buildings on a campus,are usually wired straight through.When making a connection between an Ethernet switch port and a backbone fiber optic system,you need to make sure that the signal crossover is achieved in the patch cable at one of the link.LC Patch Cable which connector has zirconia ceramic ferrule measuing 1.25mm O.D. wth either a PC or APC endface, and provides optimum insertion and return loss.And precision optical cable manufacturing services can provide a wide range of standrad and custom cables. All cables are tested,serialized and labeled in individual bags with complete test in formation

Multimode patch cord optical loss power measurement is performed using the steps described in ANSI/TIA-526-14,method A.The patch cord is substituted for the cable plant.Because patch cords are typtically no longer than 5m, the loss for the optical fiber is negligible and testing can be performed at 850nm or 1300nm. The loss measured in thistest is the loss for the patch cord connector pair.ANSI/TIA-568-C states that the maximum loss fora connector pair is 0.75dB。

After setting up the test equipment asdescribed in ANSI/TIA-526-14，method A，clean and inspect the connectors at the ends of thepathc cords to be tested.Verofu that your test jumpers have the same optical fiber type and connectors as the patch cords you are going to test .The transmit jumper should have a mandrel wrap or modal conditoner depending on the revision ANSI/TIA-526-14 being used for testing.

Because both Fiber Optic Cord connectors are easily accdssible,optical power loss should be measured in both directions.The loss for the patch cord is the average of the two measuements.If the loss for the patch cord exceeds 0.75dB in either direction,the patch cord needs be repaired or replaced.

The fiber Optic Cord is mainly used on patch panel or for the connection between outlets and terminal equipment,The quality of connectors and fibers is mainly determined by the insertion loss and return loss.

Posted by: mikofy at 04:49 AM | No Comments | Add Comment
Post contains 424 words, total size 3 kb.

Fiber optic cable has not been widely adopted for local area networks,however,because of its high cost of insallation.Networds that need extremely fast transmission rates,transminssions over long distances,or have had problems with elecriacal inteeference in the past ofen use fiber-optic cabling.

Fiber-optic cable is referred as either single-modd or multimode fiber.The term mode refers to the bundles of light that enter the fiber-optic cable.Single-mode fiber-optic cable uses only a single mode of light to propagate through the fiber cable,where multimode fiber allows multiple modes of light to propagatc.In multimode fiber-optic cable,the light bounces off the cable walls as it travels throuh the cable,which causes the singal to weaken more quickly.

Multimode fiber-optic is most ofen used as horizntal cable ,It permists multiple modes of light to propagate through the cable,which shotens cable dinstances and delibera less available bandwidth devices that use multimode fiber optic cable typically use light-emitting diodes to genarte the light that travels through that cable,however,highter bandwidth network devices such as gigabit eheemet are now usin lasers with mulitmode fiber-optic cable.The LC-LC Fiber Cable are used for non-permanent connections between patch panels, transmission equipment, etc. Pre-assembled cables allow for the implementation of complete "plug and play" solutions. When such a solution is adopted with accurate dimensioning and appropriate cable routing, it is possible to install even large cabling systems rapidly.

Single-mode fiber can be used for short distances,but due to its greater cost it is almost exclusively used for much longer distanc links in combination with LWL,ELWL or WDM solutions.Generally speaking,these solutions are designed for SMF cables with media designed for MMF can cause problems,SMF cables uses a much smaller diameter fibercord insinde the cladding:9/125um, They are usualy coloerd yellows,but like MMF cables they canbe ordered in other colors.Single mode optical fiber cable is commoly used as backbonecabling，it is also usually the cable type used in phone systems,Light travels through Fiber Optic Cords using only a single mode,meaning it travels straiht down he fiber and does not bounce off the cable walls .Because only a single mode of light travels throuht the cable,single mode fiber optical Cord support highter bandwidth and longer distances than mulitmode fiber optc cable.Devices that use single-mode fiber-fiber cable typically use laser to generate the light that travels through the cable.The Single Mode SC connector allows for quick and easy insertion via a snap-in mechanism and features a pre-radiused ceramic ferrule that minimizes back reflections.

ANSI/TIA/EIA-568-B recognizes62.5/125 micron.50/125 micron,and 8.3/125 micron single-mode optical fiber cables.ANSI/TIA/EIA-568-B states that the maximum backbone distance using single-mode fiber-optic cable is 3000 meters,and the maximum backbone distance using multimode fiber is 2,000 meters.

Posted by: mikofy at 06:24 AM | No Comments | Add Comment
Post contains 440 words, total size 4 kb.

Fiber optic patch cord is a fiber optic which be connected to the computer orequipment directly,for connecting and managering convenient.It’s used for making patch cord from equipment to fiber optic cabling. Having a thick layer of protection,it’s used to connect the optical transmitter and receiver and the terminal box.

Fiber Optic Cord are used for linking the equipment and components ,we have fiber patch cable with different fiber connector types,our low insertion loss and low back reflection .patch cord is widely applied in Telecommunication Networks ,Gigabit Ethernet and Premise Installations .Generally speaking according to different transmission media, fiber optic patch cord can be divided to common silicon-based optical fiber, Single-mode and Multi-mode patch cord, and other fiber optic patch cord that transmit through media such as plastic .However,there some tips when using the fiber patch cord,

1.Don’t bend and circle the fiber optic patch cord excessively; this will increase the attenuation of light transmission.

2. The optical module transceiver wavelength of both ends of fiber optic patch cord must be consistent, which means it should be the same wavelength of optical module at the two ends of it.

3. Must use the protective cover to protect the connectors, to avoid that dust and oil would damage the optical fiber coupling.

The LC Patch Cable from 3M is used to connect computer stations and other optical equipment with existing style networks. All fiber patch cords are constructed with the innovative 3M "GGP" high-strength coated optical fiber, providing unmatched durability and tight bend radius features for the abusive desktop environment. fiberstore patch cords are provided in a variety of lengths up to 5 meters.

Fiberstore supplies LC fiber cables and LC Patch Cord, including single mode 9/125 and multimode 50/125, multimode 62.5/125, LC-LC, LC-SC, LC-ST, LC-MU, LC-MTRJ, LC-MPO, LC-MTP, LC-FC, OM1, OM2, OM3. Other types also available for custom design. Excellent quality and fast delivery.The LC fiber cable is with a small form factor (SFF) connector and is ideal for high density applications. The LC fiber patch connector has a zirconia ceramic ferrule measuring 1.25mm O.D. with either a PC or APC end face, and provides optimum insertion and return loss. The LC fiber patch cable connector is used on small diameter mini-cordage (1.6mm/2.0mm) as well as 3.0mm cable. LC fiber cable connectors are available in cable assembled or one piece connectors.

Posted by: mikofy at 04:15 AM | No Comments | Add Comment
Post contains 394 words, total size 3 kb.

Fiber Optic Patch Cord is an fiber cable that has fiber connectors installd on one or both ends. General use of these cable assemblies include the interconnection of fiber cable systems and optics-to-electonic equipment., A push/pull type fibre optic connector similar to SC but half the size. Often found on SFP/mini GIBC's and current generation switches. NXD LC/PC connector is available in both singlemode and multimode versions. Both singlemode and multimode versions come with a zirconia ceramic ferrule with pre-polished PC profile and convex shperical end. This allows for fast polishing of the fiber and enables the installer to achieve low optical loss, while ensuring maximum repeatability. LC connectors are used to attach fiber optic cable to SFPs and patch panels. An LC-LC Fiber cable has this connector on each end. It could be used to connect two roouters together, to connect a router to a 1Gbit or 2Gbit Fibre Channel device or switch, to a patch panel, or to mangy Gigabit Eehternet devices. These cables can be purchased in either MMF or SMF verions.

The LC Patch Cable is with a small form factor (SFF) connector and is ideal for high density applications. LC fiber optic patch cord connector has a zirconia ceramic ferrule measuring 1. 25mm O. D. with a PC or APC endface, and provides optimum insertion and return loss. LC-LC fiber optic patch cables are used to send high-speed data transmissions throughout your network. LC/LC fiber optic cables connect two components with fiber optic connectors. A light signal is transmitted so there is no outside electrical interference. Our LC/LC fiber optic patch cables are 100% optically tested for maximum performance. We have all lengths and connectors available

The LC Fiber assemblies are made to order in the usa and are fully tested to guarantee top performance. Each assembly is serialized for easy identification and sealed in individual Ziploc bags. Test results are included in each order. They are constructed with the highest quality components utilizing Glass and High grade Connectors with ceramic ferrules for increased durability and accuracy. Fiberstore offer all types of LC to LC fiber optic patch cables, the LC fiber optic cables, these cables are UPC or PC polish optional, with various kinds of fiber optic cable including Riser rated, Plenum rated and RoHS compliant. These multimode duplex LC fiber optic cables are custom length and cable colors. The cables can be with 50/125 or 62. 5/125 multimode optical fiber. OM3 multimode duplex fiber cables are also available on requestThe LC to LC fiber optic cable assemblies are made to order in the usa and are fully tested to guarantee top performance. Each assembly is serialized for easy identification and sealed in individual Ziploc bags. Test results are included in each order. They are constructed with the highest quality components utilizing Glass and High

Posted by: mikofy at 03:59 AM | No Comments | Add Comment
Post contains 475 words, total size 3 kb.